Welcome Guest [Log In] [Register]
Home

Welcome to the CJ-3B Bulletin Board, the discussion forums section of the website CJ3B.info. Everyone is invited to view the postings here, but you must register as a member in order to post messages. The moderator reserves the right to remove items posted. Items may be archived in the Tech Tips section of the website. If you post a tech problem, please follow up by posting the solution when it is found, as it may be useful to other readers. For forums covering other Jeep models, see the bottom of this page.

Search for keywords or phrases anywhere in the CJ-3B Bulletin Board using Google. Enter key words here.

Google
WWW CJ-3B Bulletin Board
You're currently viewing the forums as a guest. This means there are some features you can't use. If you register, you'll be able to post messages and use member-only features such as customizing your profile and sending personal messages. Registration is simple and free.


Join the CJ-3B Bulletin Board!


If you're already a member please log in to your account to access all of our features:

Username:   Password:
Add Reply
Parking brake linkage question
Topic Started: Nov 22 2015, 06:57 AM (259 Views)
Bob W
Member
[ *   *   *   *   *  ]
I'm trying to fabricate the parking brake "lever" that goes between the front and rear cables. It is called Lever, hand brake 909811. If I can get the dimensions between the holes and maybe a photo of one that would be good!

Thanks!!!!
Bob W
www.cj3a.info
Offline Profile Quote Post Goto Top
 
SteveK
Member
[ *   *   *   *   *  ]
Bob, Since my parts are unassembled right now, I can go to my shop and get pics and dimensions for you later today, but I can't post pics on this site. Maybe (?) I can PM them to you, or if someone else already has the info, they can post it. I'm sure you'll get the info one way or the other. Are you needing just the 'pivoting arm', or anything else involved? SteveK
SteveK
62 Dispatcher
South Florida
Offline Profile Quote Post Goto Top
 
SteveK
Member
[ *   *   *   *   *  ]
Lever Arm Measurements: Overall length 11-3/8", pivot pin 9/16" wide 7/8" from end of lever, 2X holes @7/16" each 2" and 3" from center of pivot pin, plus 2X holes @1/4" approx 9" and 10" from pivot pin center. Hope that helps Cya...SteveK
SteveK
62 Dispatcher
South Florida
Offline Profile Quote Post Goto Top
 
Bob W
Member
[ *   *   *   *   *  ]
Steve, Thanks very much, that's exactly what I needed!!! If you send me a photo of the arm I will post it in this thread for everyone to see.

Thanks again,
52cj3a@gmail.com
Bob W
www.cj3a.info
Offline Profile Quote Post Goto Top
 
PapaC
Papac
[ *   *   *   *   *  ]
Debra and I are on our way home from a very difficult trip to SC.


PM sent


Charles
Charles Tate....North Mississippi

1956 WILLYS DJ3A Convertible
Doing ground up nuts and bolt restoration by almost entirely reconditioning original used or a few NOS DJ3A parts.

1962 WILLYS DJ3A Convertible. (For research and parts only)
Offline Profile Quote Post Goto Top
 
Bob W
Member
[ *   *   *   *   *  ]
Here is SteveK's photo of the lever. Thanks very much for the help!!

Posted Image
Bob W
www.cj3a.info
Offline Profile Quote Post Goto Top
 
« Previous Topic · DJ-3A Dispatcher Posts · Next Topic »
Add Reply

Other Willys Jeep forums:

The CJ-2A Page has a CJ-2A Message Board.
There is also a CJ-3A Page Forum.
For CJ-5 and Dauntless V6 postings, see the Early CJ-5 Bulletin Board.
The Old Willys Forum is dedicated to wagons and pickups.
Surrey Gala and Dispatcher Jeeps are under DJ-3A Dispatcher Posts.
The M38/M38A1/M606 Preservation Group has a forum.
For other CJ and military Jeeps, see the g503 Message Boards.
See the Forward Forum for Forward Control Jeeps.
To post ads for other Willys parts or Jeeps, see the WillysTech Buy/Sell/Swap Message Board.
For tech problems with other Willys models, try the WillysTech e-mail list.
The Bantam Trailer forum covers Jeep trailers.