| Welcome to Altezza Club Of NZ/Australia. We hope you enjoy your visit. You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are some features you can't use. If you join our community, you'll be able to access member-only sections, and use many member-only features such as customizing your profile, sending personal messages, and voting in polls. Registration is simple, fast, and completely free. http://s4.zetaboards.com/lexusaltezzaclub/topic/1148393/1/#new |
| Anyone replaced the thermostat?; RS200 3SGE | |
|---|---|
| Tweet Topic Started: Aug 25 2004, 04:40 AM (1,627 Views) | |
| Sirnixalot | Aug 25 2004, 04:40 AM Post #1 |
|
Paid-up Member
![]() ![]() ![]() ![]() ![]() ![]()
|
Not sure if i asked this on the old forum. I've got a pretty little TRD thermostat and im wondering if anyone here has replaced their thermostat before. Any hints or suggestions? |
| Damn you and your admin powers...damn you! | |
![]() |
|
| Serran | Aug 25 2004, 11:16 PM Post #2 |
|
Unregistered
|
havent done it, but how bout writing up a diy about it with pics.. so we can do it later on
|
|
|
| Sirnixalot | Aug 26 2004, 12:27 AM Post #3 |
|
Paid-up Member
![]() ![]() ![]() ![]() ![]() ![]()
|
I wrote up a DIY but the forum crashed when I posted it. So I have to write one up again. Tools needed 10mm deep socket & ratchet 12mm socket 10mm spanner (get a ratcheting one TRUST ME) Pliers (for the radiator hose clamps) Flat bladed screwdriver Small hands/arms (nows the time to teach the wife or child how to do some car stuff) Wait for car to cool thoroughly. Drain coolant from the radiator. Once the coolant has been drained, disconnect the lower radiator hose from the radiator. This will help you maneuver the thermostat housing around in the tight area. With the lower radiator hose free you need to locate the thermostat housing. It is at the top right hand side of the motor (looking at it standing in front of the car). Its under various bits of wiring harness and is a bit awkward to get to. I found the thermostat housing easier to access with both exhaust manifold heat shields removed. You do not HAVE to do this step but it will save you from being cut by them (ask me how I know). You will need the 12mm socket for this. With the heat shields out of the way and lower radiator hose free from the radiator you can now concentrate your efforts on the housing itself. It is held on by 2 10mm nuts. For the top nut you will need the 10mm deep socket, the reason you need a deep socket is for reach (it will become apparent when you attempt this). The lower nut, which you have to blindly molest the bottom of the housing till you find it, requires the 10mm spanner. Your life will be made 1000 times easier if you get a 10mm spanner that ratchets. With the nuts off (and hopefully not lost in the recesses of the engine bay somewhere) grab the flat bladed screwdriver and gently pry the housing from the block. Water will come rushing out once the housing is removed so you may want to put a bucket or a few towels under the car to catch this. Now it gets harder. Trying to get the thermostat housing to lift over the studs its slotted onto. You just have to wiggle and what not till you get it off them. If you can manage enough room, get the old thermostat out of there (it may require some convincing). The hardest part of all is getting the new thermostat to sit in the housing while you try to install everything where it went. You will be testing your dexterity every inch of the way. I found I had to reach under the housing and lift the thermostat up with a finger while I slid the housing back onto the studs (oooo that sounded far too dirty). Then you have to hold the housing there and thread the nuts back on. The lower one is the easiest to start because you can do it by hand. The upper nut you will have to use the deep socket to do. I found it easiest to use just the socket without the ratchet to start the nut and then once its snug continue to tighten it with the ratchet. With the thermostat housing tightened down you can now put back in the heat shields. Once they are on and secure you can now refill the car with coolant/water. Keep a bottle of coolant/water with you on your first drive as you will probably have to top up the coolant once the car warms up. DO NOT OPEN THE RADIATOR CAP WHEN THE CAR IS HOT!!!! I cannot stress that enough as I am not responsible for any bodily or vehicular harm which may ensue. If you find that the car is over heating find a nice spot and let it cool. Once its cooled enough that you can take the radiator cap off, fill up the radiator as required. My temps went from the notch above the halfway mark with the stock 1.1bar radiator cap and 82*C thermostat to between the half way notch and the notch below it with the TRD 1.3bar radiator cap and 71*C thermostat. Enjoy! I'll post the pix i took later. |
| Damn you and your admin powers...damn you! | |
![]() |
|
| 1 user reading this topic (1 Guest and 0 Anonymous) | |
| « Previous Topic · Engines Intakes Exhausts · Next Topic » |





![]](http://z4.ifrm.com/static/1/pip_r.png)



1:04 PM Jul 11