| Welcome to Altezza Club Of NZ/Australia. We hope you enjoy your visit. You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are some features you can't use. If you join our community, you'll be able to access member-only sections, and use many member-only features such as customizing your profile, sending personal messages, and voting in polls. Registration is simple, fast, and completely free. http://s4.zetaboards.com/lexusaltezzaclub/topic/1148393/1/#new |
| Need Help; pod related | |
|---|---|
| Tweet Topic Started: Mar 17 2007, 02:49 PM (1,402 Views) | |
| blitzNUR | Mar 17 2007, 02:49 PM Post #1 |
|
Lowered
![]() ![]() ![]() ![]() ![]()
|
just decided i wanted a pod in my rs200 ... and ive readed all the forums on that its on good on the engine and it runs crap and all ... so today i got a 90 degee bend and then onto a stright pipe and then pod. and seriously feels like crap ... and im soo piseed of cos i wasted that money for nothing. or if someone could direct me some how to fix this. cheers |
Hi !!
| |
![]() |
|
| Jase | Mar 17 2007, 02:51 PM Post #2 |
|
Auckland, NZ > Tsing Yi, HK
![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
Have you reset your ECU? What pod filter? |
| |
![]() |
|
| blitzNUR | Mar 17 2007, 02:56 PM Post #3 |
|
Lowered
![]() ![]() ![]() ![]() ![]()
|
ill post a photo in 3 mins |
Hi !!
| |
![]() |
|
| Muzza | Mar 17 2007, 02:59 PM Post #4 |
|
Hamilton
![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
Where are you |
|
Muzza HKS RS Induction. Tom's lightened flywheel,TRD Clutch,TRD Clutch Cover Apexi SAFCII,Gizzmo Shiftlight-Launch conntroller,Pivot speedmetre-x Cusco Front Strutbrace Mintex M116 Brakepads | |
![]() |
|
| blitzNUR | Mar 17 2007, 03:00 PM Post #5 |
|
Lowered
![]() ![]() ![]() ![]() ![]()
|
![]() im in auckland i might just pull the earth for 30 mins or so |
Hi !!
| |
![]() |
|
| greeneyes | Mar 17 2007, 03:12 PM Post #6 |
|
Targa Master
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
Swap the straight pipe to the other end of the curved pipe, so the MAF sensor is furthest from the filter and in a more linear airflow area. Might help- |
|
The Girl's KE70- http://www.rollaclub.com/board/topic/42407-the-girls-ke70/ How NOT to build a rally car- http://www.rollaclub.com/board/topic/64027...ld-a-rally-car/ | |
![]() |
|
| jasestu | Mar 17 2007, 05:45 PM Post #7 |
|
caffeinated...
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
|
And of course double check that the MAF is installed the right way round (sorry if that sounds patronising). |
|
ex RS200 Z ed 6MT | Bay of Plenty, New Zealand | |
![]() |
|
| Noel | Mar 17 2007, 10:05 PM Post #8 |
|
Virtual visitor
![]() ![]() ![]() ![]() ![]()
|
I think it's because of the small filter you have on the breather pipe..... i tried that but it barely ticked over, i think it needs a bit of vacuum to run right.... can you try and tap a pipe for it onto the main intake.... |
|
From Ireland... Drive an RS200Z tiptronic | |
![]() |
|
| blitzNUR | Mar 18 2007, 07:43 AM Post #9 |
|
Lowered
![]() ![]() ![]() ![]() ![]()
|
it runs ... just when i open the throttle the car takes about 3 - 4 secs to relise that i actually stepped on the gas ... but ill try what you said tonight noel cheers guys |
Hi !!
| |
![]() |
|
| Twincams | Mar 20 2007, 12:37 PM Post #10 |
|
Stock
![]() ![]() ![]() ![]()
|
usually when i am using the stock ecu with the open pod, i'll drive with very slow throttle angle changes throughout the whole rev range for the 1st week or so.... this will allow the ecu enough time to make any fuel and ignition timing adjustments on its own... |
| |
![]() |
|
| alexlegault | May 1 2010, 07:03 PM Post #11 |
|
Soccer Mom
![]() ![]() ![]()
|
http://z4.invisionfree.com/lexusaltezzaclu...showtopic=10310 my prob is kinda similar. i think you should punch a hole in the intake after the afm for that hose you have sticking out of the engine breathing to atmospheric preasre. alex. |
![]() |
|
| 1 user reading this topic (1 Guest and 0 Anonymous) | |
| « Previous Topic · Engines • Intakes • Exhausts · Next Topic » |





![]](http://z4.ifrm.com/static/1/pip_r.png)




8:29 PM Jul 11